Cabletron Systems 6C105 Instalační příručka

6E308-24 and 6E308-48 Ethernet Modules Installation GuideRESETCOMCPU1X12X1X12XGROUP1GROUP2GROUPGROUPSELECTFAST ENET6E308-24RESETCOMCPUGROUPGROUPSELECT

viii Contents3INSTALLATION3.1 Unpacking the Module ... 3-23.2 Install

Figures ixFiguresFigure Page1-1 The 6E308-24 and 6E308-48 Modules ... 1-23-1 I

xTablesTabl e Page3-1 Contents of Module Carton ...3-24-1 LANV

About This Guide xiAbout This GuideWelcome to the Enterasys Networks™ 6E308-24 and 6E308-48 Fast Ethernet Modules Installation Guide. This guide descr

Structure of This Guidexii About This GuideSTRUCTURE OF THIS GUIDEThis guide is organized as follows:This chapter provides preliminary information to

Document ConventionsAbout This Guide xiiiDOCUMENT CONVENTIONSThe guide uses the following conventions:NOTE: Calls the reader’s attention to any item o

Getting Helpxiv About This GuideGETTING HELPFor additional support related to the module or this document, contact Enterasys Networks™ using one of th

Introduction 1-11IntroductionThis chapter introduces the 6E308-24 and 6E308-48 fiber optic Fast Ethernet modules. The 6E308-24 module (Figure 1-1) fea

1-2 IntroductionFigure 1-1 The 6E308-24 and 6E308-48 Modules48 10BASE-FLFiber Optics Ports(10 Mbps)RESETCOMCPUFAST ENET6H308-48GROUPGROUPSELECT4GROUP3

ConnectivityIntroduction 1-31.1 CONNECTIVITYThe module connects to Ethernet networks or workstations through the front panel connectors. The ports are

Remote Monitoring (RMON)1-4 Introduction1.4 REMOTE MONITORING (RMON)The module supports all nine Ethernet RMON groups. The Statistics, Alarms, Events

Flow ControlIntroduction 1-5Administrators can configure up to four rate limit rules per port; however, each rule must not include conflicting 802.1p

802.1 Port Priority1-6 Introduction1.10 802.1 PORT PRIORITYThe 802.1 port priority is used to assign a default priority to the frames received without

Switching OptionsIntroduction 1-71.13 SWITCHING OPTIONSThe module provides 802.1Q switching between all of the front panel interfaces. In the 802.1Q m

Network Requirements 2-12Network RequirementsBefore installing the module, review the requirements and specifications referred to in this chapter conc

10BASE-FL Fiber Optic Network2-2 Network RequirementsThe link segment can be tested with a fiber optic attenuation test set that is adjusted for an 85

Installation 3-13InstallationThis chapter provides the instructions to install the 6E308-24 or 6E308-48. A Phillips screwdriver is required to install

Completing the Installation3-8 Installation3.1 UNPACKING THE MODULEUnpack the module as follows:1. Open the box and remove the packing material protec

Connecting to the NetworkInstallation 3-93.3 INSTALLING THE MODULE INTO THE MATRIX E7 CHASSISThe module can be installed in any of the slots that are

NOTICEEnterasys Networks and its licensors reserve the right to make changes in specifications and other information contained in this document withou

Completing the Installation3-8 InstallationFigure 3-1 Installing the Module into the MATRIX E7 Chassis3544_0245676C107123BackplaneConnectorsPOWER OK/R

Connecting to the NetworkInstallation 3-95. Examine the module for damage. If any damage exists, DO NOT install the module. Immediately contact Entera

Completing the Installation3-8 Installation3.4 INSTALLING THE MODULE INTO THE 6C105 CHASSISCertain restrictions may apply when installing the module i

Connecting to the NetworkInstallation 3-9Figure 3-2 Installing the Module into the 6C105 ChassisRESETCOMCPUFAST ENET6H308-241X12X1X12XGROUP1GROUP2GROU

Completing the Installation3-8 Installation3.5 CONNECTING TO THE NETWORKThis section provides the procedures for connecting fiber optic cable from the

Connecting to the NetworkInstallation 3-9Figure 3-3 Connecting a Fiber Optic Segment to the Module3. Plug the other end of the cable into the appropri

Completing the Installation3-8 Installation4. Verify that a link exists by checking that the port RX (Receive) LED is ON (flashing amber, blinking gre

Troubleshooting 4-14TroubleshootingThis chapter provides information concerning the following:• Using LANVIEW (Section 4.1)• Troubleshooting Checklist

Using LANVIEW4-2 TroubleshootingFigure 4-1 LANVIEW LEDsTable 4-1 describes the LED indications and provides recommended actions as appropriate.NOTE: T

Using LANVIEWTroubleshooting 4-3Table 4-1 LANVIEW LEDsLED Color State Recommended ActionCPU Off Power off. Ensure chassis has adequate power.Red Blink

FCC NOTICEThis device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not cause harm

Using LANVIEW4-4 TroubleshootingTX (Transmit)Off Port enabled, and no activity.Should flash green every two seconds indicating BPDUs being sent if STA

Troubleshooting ChecklistTroubleshooting 4-54.2 TROUBLESHOOTING CHECKLISTIf the module is not working properly, refer to Table 4-2 for a checklist of

Troubleshooting Checklist4-6 TroubleshootingCannot contact the module through in-band management.IP address not assigned. Refer to the MATRIX E7 and S

Using the RESET ButtonTroubleshooting 4-74.3 USING THE RESET BUTTONThe RESET button shown in Figure 4-2 resets and re-initializes the module.Figure 4-

Specifications A-1ASpecificationsThis appendix provides operating specifications for the Enterasys Networks 6E308-24 and 6E308-48 modules. Enterasys N

Fiber BudgetA-2 SpecificationsA.2 FIBER BUDGETWhen using a 62.5/125 micron fiber optic cable, it is important to consider the cable type and the assoc

COM Port Pinout AssignmentsSpecifications A-3A.3 COM PORT PINOUT ASSIGNMENTSThe COM port is a serial communications port that supports Local Managemen

Mode Switch Bank Settings and Options B-1BMode Switch Bank Settings and OptionsThis appendix covers the following items:• Required tools (Section B.1)

ENTERASYS NETWORKS, INC.PROGRAM LICENSE AGREEMENTBEFORE OPENING OR UTILIZING THE ENCLOSED PRODUCT,CAREFULLY READ THIS LICENSE AGREEMENT.This document

Setting the Mode SwitchesB-2 Mode Switch Bank Settings and OptionsB.2 SETTING THE MODE SWITCHESFigure B-1 shows the location of the mode switches and

Setting the Mode SwitchesMode Switch Bank Settings and Options B-3• Switch 6 – Forced BootP. DO NOT attempt a Forced BootP unless a BootP server has b

FLASH UpgradeB-4 Mode Switch Bank Settings and OptionsB.3 FLASH UPGRADEFLASH upgrade is available for the SmartSwitch to expand from 8 to 16 MB. This

FLASH UpgradeMode Switch Bank Settings and Options B-5B.3.2 Installing the FLASH ModuleTo install a FLASH module, refer to Figure B-3 and proceed as f

Index-1IndexNumerics10BASE-FLrequirements 2-1802.1p Port Priorityintroduction to 1-6BBroadcast Suppressionintroduction to 1-4CCable specifications10BA

Index-2PPort redirect functionintroduction to 1-4RRate Limiting 1-4Receive LEDsviewing of 4-1Redirect functionsport and VLANintroduction to 1-4Regulat

5. UNITED STATES GOVERNMENT RESTRICTED RIGHTS. The enclosed Product (i) was developed solely at private expense; (ii) contains “restricted computer so

DECLARATION OF CONFORMITYApplication of Council Directive(s): 89/336/EEC73/23/EECManufacturer’s Name: Enterasys Networks, Inc.Manufacturer’s Address:

Contents viiContentsFigures ..............................