Cabletron Systems HSIM-FE6 Uživatelská příručka

Title PageHSIM-FE6FEPIM 1FEPIM 2SP 9032555-03 HSIM-FE6User’s Guide

Contentsviii HSIM-FE6 User’s Guide

HSIM-FE6 User’s Guide ix FIGURES Figure Page1-1 HSIM-FE6..

x HSIM-FE6 User’s Guide TABLES Table Page 1-1 FEPIM Options ...

HSIM-FE6 User’s Guide 1-1 CHAPTER 1INTRODUCTION Welcome to the Cabletron Systems HSIM-FE6 User’s Guide . This manual describes the HSIM-FE6 and prov

Chapter 1: Introduction 1-2 HSIM-FE6 User’s Guide Chapter 3, LANVIEW LEDs , describes how to use the HSIM-FE6 LEDs to monitor the HSIM performance

FEPIM OptionsHSIM-FE6 User’s Guide 1-3 1.3 FEPIM OPTIONS The FEPIM options for the HSIM-FE6 are listed in Table 1-1. Check the Release Notes with the

Chapter 1: Introduction 1-4 HSIM-FE6 User’s Guide 1.5 GETTING HELP For additional support related to this device or document, contact the Cabletron

Related DocumentationHSIM-FE6 User’s Guide 1-5 1.6 RELATED DOCUMENTATION The documentation for the host device in which the HSIM-FE6 is to be install

Chapter 1: Introduction 1-6 HSIM-FE6 User’s Guide

HSIM-FE6 User’s Guide 2-1 CHAPTER 2INSTALLATION To install the HSIM-FE6 the following items are required: • Antistatic wrist strap • Phillips screwdr

Chapter 2: Installation 2-2 HSIM-FE6 User’s Guide 2.2 INSTALLING FAST ETHERNET (PORT) INTERFACE MODULES Fast Ethernet (Port) Interface Modules (FEPI

Installing Fast Ethernet (Port) Interface ModulesHSIM-FE6 User’s Guide 2-3Figure 2-1 Removing the FEPIM Coverplate2. Refer to Figure 2-2. Gently pull

Chapter 2: Installation2-4 HSIM-FE6 User’s GuideFigure 2-2 Installing the FEPIM4. Press down firmly on the FEPIM until the pins slide all the way into

Installing the HSIM-FE6HSIM-FE6 User’s Guide 2-52.3 INSTALLING THE HSIM-FE6An HSIM-FE6 can be installed in any Cabletron Systems device that supports

Chapter 2: Installation2-6 HSIM-FE6 User’s Guide5. Remove and save the two faceplate mounting screws securing the HSIM coverplate and remove the cover

Installing the HSIM-FE6HSIM-FE6 User’s Guide 2-7Figure 2-4 Installing the HSIM-FE67. Align the connector on the HSIM-FE6 with the connector on the mod

Chapter 2: Installation2-8 HSIM-FE6 User’s Guide9. Secure the HSIM-FE6 to the module faceplate using the mounting screws saved in step 5.10. Secure th

Connecting to the NetworkHSIM-FE6 User’s Guide 2-98. Press down firmly on the HSIM-FE6 until the connector slides all the way onto the HSIM pins. Ensu

Chapter 2: Installation2-10 HSIM-FE6 User’s Guide2.4.1 Connecting a Fiber Optic Segment to the FEPIMCabletron Systems offers fiber optic cables that us

Connecting to the NetworkHSIM-FE6 User’s Guide 2-114. Verify that a link exists by checking that the port receive LED is ON (flashing amber, blinking

HSIM-FE6 User’s Guide i NOTICE Cabletron Systems reserves the right to make changes in specifications and other information contained in this document

Chapter 2: Installation2-12 HSIM-FE6 User’s GuideA schematic of a straight-through and a crossover cable is shown in Figure 2-6. If the wires do not c

Connecting to the NetworkHSIM-FE6 User’s Guide 2-133. Verify that a link exists by checking that the port receive LED is on (flashing amber, blinking

Chapter 2: Installation2-14 HSIM-FE6 User’s Guide

HSIM-FE6 User’s Guide 3-1CHAPTER 3LANVIEW LEDsThis chapter describes how to use the LANVIEW LEDs to monitor the HSIM-FE6 status and diagnose HSIM-FE6

Chapter 3: LANVIEW LEDs3-2 HSIM-FE6 User’s Guide 3.2 FE-100TX LEDThe optional FE-100TX has one LED labeled 10/100. The 10/100 LED together with the RX

HSIM-FE6 Local ManagementHSIM-FE6 User’s Guide 3-3f3.3 HSIM-FE6 LOCAL MANAGEMENTFor information concerning Local Management for the HSIM-FE6, refer to

Chapter 3: LANVIEW LEDs3-4 HSIM-FE6 User’s Guide

HSIM-FE6 User’s Guide A-1APPENDIX ASPECIFICATIONSThis chapter lists the specifications and regulatory requirements for the HSIM-FE6. Cabletron Systems

Appendix A: SpecificationsA-2 HSIM-FE6 User’s GuideA.4 REGULATORY COMPLIANCEThis equipment meets the following safety and electromagnetic compatibility

HSIM-FE6 User’s Guide B-1APPENDIX BFEPIM SPECIFICATIONSThis appendix provides specifications for the Fast Ethernet (Port) Interface Modules. Cabletron

Noticeii HSIM-FE6 User’s Guide INDUSTRY CANADA NOTICE This digital apparatus does not exceed the Class A limits for radio noise emissions from digita

Appendix B: FEPIM SpecificationsB-2 HSIM-FE6 User’s GuideB.2 FE-100FXThe FE-100FX shown in Figure B-2 uses an SC style connector that supports multimod

FE-100F3HSIM-FE6 User’s Guide B-3B.3 FE-100F3The FE-100F3 shown in Figure B-3 uses an SC style connector that supports single mode fiber optic cabling.

Appendix B: FEPIM SpecificationsB-4 HSIM-FE6 User’s Guide

NoticeHSIM-FE6 User’s Guide iii CABLETRON SOFTWARE PROGRAM LICENSE 1. LICENSE. You have the right to use only the one (1) copy of the Program provide

Noticeiv HSIM-FE6 User’s Guide SAFETY INFORMATIONCLASS 1 LASER TRANSCEIVERSTHE HSIM-FE6 GIGABIT ETHERNET MODULES USECLASS 1 LASER TRANSCEIVERS. READ

NoticeHSIM-FE6 User’s Guide v DECLARATION OF CONFORMITY Application of Council Directive(s): 89/336/EEC73/23/EEC Manufacturer’s Name: Cabletron Syste

Noticevi HSIM-FE6 User’s Guide

HSIM-FE6 User’s Guide vii CONTENTS CHAPTER 1 INTRODUCTION 1.1 Using This Manual..................