Cabletron Systems 9C106 Uživatelská příručka

9031994-01 SmartSwitch 9000-6 Slot9C306 System MonitorUser’s Guide

Introduction1-2 Figure 1-1. The 9C306 System MonitorSTATUSCOM1COM2EPIMLNKEPIM-TSM9C306

1-3Introduction Hot Swapping The 9C306 System Monitor can be removed from the chassis while the SmartSwitch 9000-6 Slot is running without interrupti

Introduction1-4 Getting Help For additional support related to this device or document, contact Cabletron Systems using one of the following methods:

2-1 Chapter 2 Installing the 9C306 System Monitor The 9C306 System Monitor is installed in the slot marked SM at the right front side of the SmartSwi

Installing the 9C306 System Monitor2-2 If the SmartSwitch 9000-6 Slot chassis has not been powered up, make sure that all modules have been properly

3-1 Chapter 3 9C306 System Monitor Operation The 9C306 System Monitor, monitors several chassis environmental parameters, provides multiple out-of-ba

9C306 System Monitor Operation3-2 System Voltages The 9C306 System Monitor monitors speciÞc system power parameters to ensure that they are within ac

3-39C306 System Monitor Operation The STATUS LED indicates the current status of the System Monitor processor and peripherals. The possible states an

9C306 System Monitor Operation3-4 COM1 and COM2 Ports The 9C306 System Monitor front panel has two RJ45 communication ports for RS232 serial communic

4-1 Chapter 4 Specifications Safety The 9C306 System Monitor, when properly installed in the SmartSwitch 9000-6 Slot chassis, complies with the follow

Specifications4-2 Physical Dimensions 48.3 H x 30.5 W x 36.8 D centimeters(19 H x 1.2 W x 14.5 D inches) Weight Unit: 2.27 kilograms (5 pounds)Shippin

A-1 Appendix A EPIM Specifications Introduction The 9C306 System Monitor provides a port for Cabletron Systems EPIMs. EPIMs allow connection to the ma

EPIM SpecificationsA-2Figure A-1. EPIM-T Crossover SwitchEPIM-F2 The EPIM-F2 supports Multimode Fiber Optic cabling. Each EPIM has an internal Cabletro

A-3EPIM-F2Transmitter power parameters are listed Table A-2.Table A-1. EPIM-F2 Receiver SpecificationsParameter Typical Value Worst CaseWorst Case Budg

EPIM SpecificationsA-4EPIM-F3The EPIM-F3 supports Single Mode Fiber Optic cabling. It has an internal Cabletron Systems FOT-F Fiber Optic Transceiver a

A-5EPIM-F3Table A-3. EPIM-F3 SpecificationsParameter Typical Minimum MaximumTransmitter Peak Wave Length 1300 nm 1270 nm 1330 nmSpectral Width 60 nm -

EPIM SpecificationsA-6EPIM-A and EPIM-X (AUI Port)The EPIM-A is a DB15 female connector used to attach segments to an external transceiver. The EPIM-X

B-1Appendix BUninterruptible Power Supply (UPS)IntroductionThe SmartSwitch 9000-6 Slot can be connected to a UPS to provide an uninterruptible source

Uninterruptible Power Supply (UPS)B-2Figure B-1. Connecting the SM Module to a UPSConfiguring COM Port for UPSAfter the UPS has been connected to the C

B-3Monitoring UPSMonitoring UPSInformation about the operation of the UPS is obtained via Remote SNMP Management or locally by the LCD on the front of

iNotice Notice Cabletron Systems reserves the right to make changes in speciÞcations and other information contained in this document without prior n

Uninterruptible Power Supply (UPS)B-4

Noticeii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not

iiiNotice Declaration of ConformityAddendum Application of Council Directive(s): 89/336/EEC73/23/EEC ManufacturerÕs Name: Cabletron Systems, Inc. Man

Noticeiv

v Contents Chapter 1 Introduction Features ...

Contentsvi

1-1 Chapter 1 Introduction The 9C306 System Monitor, shown in Figure 1-1, provides out-of-band management capabilities, and environmental/power monit