Cabletron Systems 9F426-02 Uživatelská příručka

SmartSwitch 90009F426-02User’s Guide 9031692-03

Contentsviii Appendix A FPIM Specifications FPIM-00 and FPIM-01...

1-1 Chapter 1 Introduction The 9F426-02 FDDI SmartSwitch ® Module shown in Figure 1-1, is a three port switch module with two front panel FDDI inter

Introduction1-2 Management The 9F426-02 module has two full implementations of SMT (Version 7.3), one per interface, and SNMP for local and remote ma

1-3Introduction Figure 1-1. The 9F426-02 Module1212ABFDDI1ABFDDI29F426-02FDDISMB CPUINB

Introduction1-4 Related Manuals The manuals listed below should be used to supplement the procedures and technical data contained in this manual.Smar

2-1 Chapter 2 Installing the SmartSwitch 9000 Module This module uses FPIMs for the front panel connections. They are not shipped with the module and

Installing the SmartSwitch 9000 Module2-2 Figure 2-1. Installing an FPIM User-Accessible Components Figure 2-2 shows the various components that are

2-3Installing the SmartSwitch 9000 Module Figure 2-2. User Accessible Components An eight-position DIP switch is located on the module card as shown

Installing the SmartSwitch 9000 Module2-4 See the Cautions at the end of this table. Table 2-1. Function of DIP Switch Switch Function Description8

2-5Installing the SmartSwitch 9000 Module Installing the Module into the SmartSwitch 9000 Chassis To install the SmartSwitch 9000 module, follow the

Installing the SmartSwitch 9000 Module2-6 Figure 2-3. Installing the 9F426-02 ModuleMetal Back-PanelModule GuidesModuleJack for ESDWrist StrapPlastic

2-7Installing the SmartSwitch 9000 Module The Reset Switch The Reset switch is located under the top plastic tab as shown in Figure 2-4. It serves tw

Installing the SmartSwitch 9000 Module2-8

3-1 Chapter 3 Operation The 9F426-02 module is capable of switching any three, of five possible interfaces, depending on how it is configured. The INB-

Operation3-2 System Management Buses There are two management channels within the SmartSwitch 9000 system: the SMB-1 and the SMB-10. These buses prov

3-3Operation DC/DC Converter The DC/DC converter converts the 48 VDC on the system power bus to the necessary operating voltages for its host network

Operation3-4 i960 Core The i960 core provides the SNMP protocol stacks, to support industry-standard MIBs. Additionally, Cabletron enterprise extensi

4-1 Chapter 4 LANVIEW LEDs The front panel LANVIEW LEDs indicate the status of the module and may be used as an aid in troubleshooting. Shown in Figu

LANVIEW LEDs4-2 The functions of the two System Status LEDs, System Management Bus (SMB) and the CPU, are listed in Table 4-1.The function of the INB

4-3LANVIEW LEDs The function of the FDDI receive LEDs is listed in Table 4-4.The function of the FDDI Transmit LED is listed in Table 4-5.The FDDI st

iNotice Notice Cabletron Systems reserves the right to make changes in specifications and other information contained in this document without prior n

LANVIEW LEDs4-4 The functions of the FDDI Status LEDs are listed in Table 4-6. Table 4-6. FDDI Status LEDs A P S B STATE Green N/A N/A Gr

5-1 Chapter 5 Specifications Technical Specifications CPUIntel i960 RISC based microprocessorMemory4 Meg. Local RAM (expandable to 12 Meg.)4 Meg. Flash

Specifications5-2SafetyThis equipment meets the safety requirements of:• UL 1950• CSA C22.2 No. 950 • EN 60950• IEC 950• EMI Requirements of FCC Part 1

A-1Appendix AFPIM SpecificationsThis SmartSwitch 9000 module uses Fiber Port Interface Modules (FPIM) to provide front panel cable connections. The FPI

FPIM SpecificationsA-2Transmitter power parameters are listed in Table A-2.The link distance is up to 2 kilometers on the multimode fiber-optic cable as

A-3FPIM-05 and FPIM-07FPIM-05 and FPIM-07The FPIM-05 and FPIM-07 provide a single-mode fiber connection. The FPIM-05 uses a MIC-style connector and the

FPIM SpecificationsA-4

Noticeii FCC Notice This device complies with Part 15 of the FCC rules. Operation is subject to the following two conditions: (1) this device may not

iiiNotice DECLARATION OF CONFORMITYADDENDUM Application of Council Directive(s): 89/336/EEC73/23/EEC Manufacturer’s Name: Cabletron Systems, Inc. Man

Noticeiv Safety Information CLASS 1 LASER TRANSCEIVERSThe FPIM-05 and FPIM-07 are Class 1 Laser ProductsThe FPIM-05 and FPIM-07 use Class 1 Laser tra

vNotice Safety Information CLASS 1 LASER TRANSCEIVERSLaser Radiation and Connectors When the connector is in place, all laser radiation remains withi

Noticevi

vii Contents Chapter 1 Introduction Features..........................